Front Hood Lift Supports Shocks Springs Props for Hummer H3 2006-2010
Rated 3.5/5 based on 11 customer reviews

Front Hood Lift Supports Shocks Springs Props for Hummer H3 2006-2010

  • Product SKU: C122-1076935
  • Availability: In Stock
$71.04
Hurry! only 1 left in stock!
Ask about this product
Your message has been successfully sent to the store owner!
Payment
Front Hood Lift Supports Shocks Springs Props for Hummer H3 2006-2010Features:Easy to install.YQ compression gas springs type, also known as free type gas spring, supporting bar, nitrogen spring is a high-pressure gas sealed in the cylinder, the piston produced by the elastic features of the product. The product does not need to work at the outside power, constant lifting force. Fully open the rear door is widely used in automobile, hood, back door luggage, mechanical equipment, construction machinery, furniture, fitness equipment, and other fields. It has a long life, easy to control, no maintenance and so on.Specification:Compressed Length: 15.8cmExtended Length: 40cmSuitable for For 2006-2010 Hummer H3Installment:1. Use Safety stands whenever a procedure requires you under the vehicle or supports. Or have someone hold the lid open for you so that they can raise or lower it as needed.2. Before removing the old lift support, inspect the end connections and compare them to the units on your vehicle to make sure that they are the same As well as the extended length.3. Remove the old support from the vehicle by placing a small flat headed screw driver under the U shaped band on the ends of the support. Slowly turn the screw driver and it will lift up on the band approx.1/8", then pull the support away from the vehicle and it will release.4. To install the new supports do the same procedure in reverse. DO NOT jam the new support end over the ball socket without lifting the U band slightly or damage may occur.5. Lift Supports need to be installed fully extended. In most cases you just can't compress them unless they are on the vehicle. If you have any issues during the installation PLEASE contact us. Never force a support.6. If the ends are not lining up the support may need to be turned. To do this attach the shaft end of the support to the vehicle and then turn the entire body of the support clockwise unit the ends line up.Package Included:2 X Front Hood Gas Lift Supports4 X Ball Screws
,,,,,,,,,
Front Hood Lift Supports Shocks Springs Props for Hummer H3 2006-2010Features:Easy to install.YQ compression gas springs type, also known as free type gas spring, supporting bar, nitrogen spring is a high-pressure gas sealed in the cylinder, the piston produced by the elastic features of the product. The product does not need to work at the outside power, constant lifting force. Fully open the rear door is widely used in automobile, hood, back door luggage, mechanical equipment, construction machinery, furniture, fitness equipment, and other fields. It has a long life, easy to control, no maintenance and so on.Specification:Compressed Length: 15.8cmExtended Length: 40cmSuitable for For 2006-2010 Hummer H3Installment:1. Use Safety stands whenever a procedure requires you under the vehicle or supports. Or have someone hold the lid open for you so that they can raise or lower it as needed.2. Before removing the old lift support, inspect the end connections and compare them to the units on your vehicle to make sure that they are the same As well as the extended length.3. Remove the old support from the vehicle by placing a small flat headed screw driver under the U shaped band on the ends of the support. Slowly turn the screw driver and it will lift up on the band approx.1/8", then pull the support away from the vehicle and it will release.4. To install the new supports do the same procedure in reverse. DO NOT jam the new support end over the ball socket without lifting the U band slightly or damage may occur.5. Lift Supports need to be installed fully extended. In most cases you just can't compress them unless they are on the vehicle. If you have any issues during the installation PLEASE contact us. Never force a support.6. If the ends are not lining up the support may need to be turned. To do this attach the shaft end of the support to the vehicle and then turn the entire body of the support clockwise unit the ends line up.Package Included:2 X Front Hood Gas Lift Supports4 X Ball Screws,,,,,,,,,

SHIPPING

Due to very hight demand and order volume, orders can take up to 7-15 days to be delivered. However most orders are delivered within 7-10 days.

  • Complimentary ground shipping within 1 to 7 business days
  • Next-day and Express delivery options also available
  • See the delivery FAQs for details on shipping methods, costs and delivery times

30 DAYS MONEY BACK GUARANTEE

Did you receive the wrong or non-compliant product? You will have the opportunity to receive it again at no cost.

Contact us and communicate your request.

*All shipping times exclude customs delays.